|
|
|
|
MT-1024 PEELABLE MASKANT
Characteristics: Opaque Red; Viscosity – 5000-5500 cps, #5 spindle, 20 rpm; Weight per gallon, approx. 8.0 pounds. Flash point – 24 degrees F. T.C.C.; 4.8# per gallon VOC. MT-1024 is butyl rubber compound containing toluene and vm&p naphtha. MT-1024 is suitable for use in the following: Electroless Nickel Plating Chemical Milling Hard Coat AnodizingMost acid solutions APPLICATION PROCEDURE1. Before applying MT-1024, make sure the metal part is clean and free from grease, dirt and the like. The adhesion of MT-1024 could be compromised if the part is not clean prior to applying MT-1024. 2. Stir MT-1024 prior to use. It is common for some settling to occur and this is normal. Stir only enough to bring the mixture to a homogenous mixture. Over-mixing can incorporate air into the product. 3. Apply MT-1024 to the area to be masked by brushing or dipping. Use a camel hair brush to apply MT-1024. If MT-1024 becomes to thick, use MT-1024 reducer to bring the product to the desired consistency. MT-1024 can be sprayed with proper dilution. Consult directions on spray equipment to determine proper viscosity for spraying. 4. As a general rule, two coats of MT-1024 are needed to achieve desired results. Depending upon the application, temperature of the solution, length of time in the solution, ph of the solution and other factors, it may be necessary to apply three coats to achieve desired results. Apply coats perpendicular if possible to cover the area to be masked more thoroughly. 5. Allow at least thirty minutes dry time between coats. Make sure that MT-1024 has lost all solvent odor before applying additional coats. An overnight air dry is recommended before immersing a part masked with MT-1024 into a solution. Faster drying can be accomplished by force drying the masked part over a hot plate or in a forced air oven. Do not exceed 140 degrees F for forced drying and no longer than fifteen minutes. Make sure MT-1024 has lost all solvent odor before placing part over a hot plate or in a forced air oven. 6. After the first coat dries, carefully trim any excess MT-1024 material with a sharp knife making sure not to lift the material from the desired edge. If some lifting should occur, use a small camel hair brush and carefully apply a small amount of MT-1024 to the area to seal it. If additional coats are applied, paint or dip to the cut edge. Allow material to dry thoroughly before placing part in solution. 7. MT-1024 is suitable for use in normal alkaline cleaning operations including reverse electro clean operations. However, do not leave part in this alkaline solution for extended periods of time. As a general rule, two minutes or less in an alkaline solution will not cause degradation of the material. 8. MT-1024 can normally be peeled from the part if the part is warm. If the part is cold, soak briefly in warm water for removal of the maskant. For removal in small or recessed areas, MT-1024 Reducer will remove the maskant. Toluene will also remove the maskant and the maskant can be burned from the part. Consult state and federal regulations before burning material from part as smoke will be released.
CAUTIONMT-1024 CONTAINS VOLATILE SOLVENTS. ALWAYS WORK IN A WELL-VENTILATED AREA AND WEAR APPROPRIATE GLOVES, EYE PROTECTION AND BREATHING EQUIPMENT. KEEP MT-1024 AWAY FROM OPEN FLAMES AND STORE IN TEMPERATURES BETWEEN 50 DEGREES F AND 100 DEGREES F. KEEP ALL CONTAINERS CLOSED WHEN NOT IN USE. OBSERVE ALL EPA, OSHA AND ALL OTHER FEDERAL AND STATE REGULATIONS. CUSTOMERS ARE ASKED TO EVALUATE THIS PRODUCT PRIOR TO USE TO DETERMINE SUITABILITY FOR THEIR PARTICULAR APPLICATION. APPLICATION PROCEDURES AND SUGGESTED USES DO NOT CONSTITUTE ENDORSEMENT OF THIS PRODUCT FOR ANY PARTICULAR USE OR PURPOSE. ALWAYS CONSULT MATERIAL SAFETY DATA SHEET PRIOR TO USUAGE AND FOLLOW ALL STATE AND FEDERAL REGULATIONS REGARDING MATERIAL SAFETY DATA SHEETS. EMERGENCY TELEPHONE NUMBER: 1-800-535-5053 TERMS, CONDITIONS AND WARRANTYThe following terms, conditions and warranty extend to the sale of all MaskTec, Inc. (hereinafter “Seller”) parts, products or services requested by customers or any other party. All specifications and representations made on the face of this document are incorporated herein by reference. WARRANTY: Unless otherwise noted, Seller warrants for a period of one year from the date of manufacture that all products delivered to the customer shall be free from defects. All warranty claims with respect to any alleged defect must be received by the seller within one year after manufacture date of the goods. Upon timely receipt of verified claims, Seller, at Seller’s option, will replace or refund the purchase of the allegedly defective materials. SELLER DISCLAIMS ALL OTHER WARRANTIES IN CONNECTION WITH THE GOODS OR SERVICES, EXPRESSED OR IMPLIED, AS TO ANY MATTER WHATSOEVER, INCLUDING WITHOUT LIMITATION, DISCLAIMER OF: DESCRIPTION, QUALITY DESIGN, PERFORMANCE, SPECIFICATION, CONDITION, MERCHANTIBILITY, AND FITNESS FOR ANY PARTICULAR PURPOSE. SELLER ALSO DISCLAIMS ALL OTHER WARRANTIES IN CONNECTION WITH GOODS PROVIDED TO BUYER, WHICH ARE NOT PROPERLY MAINTAINED, USED OR INSPECTED.
LIMITATION OF DAMAGES: The liability, if any, of Seller and its agents, servants, representatives or employees with regards to goods and/or services for any claims, costs damages, losses liabilities and expenses for which they are or were legally liable, whether arising in negligence or in tort, contract or otherwise, shall not exceed in the aggregate the agreed upon price for the goods or services. In no event shall the Seller or its agents, servants, representatives or employees be liable for indirect, special or consequential damages (subject to state by state application of Mag-Moss (16CFR 701.3). APPLICABLE LAW AND DISPUTE: Any dispute arising under the sale of goods shall be governed by the laws of the State of Arkansas and applicable federal law. Any dispute, which arises which, is not resolved by the parties shall be referred to and exclusively decided pursuant to commercial arbitration rules of the American Arbitration Association in Texarkana, Arkansas and its decision shall be enforceable upon entry with a court of competent jurisdiction. The arbitrator shall not have the power or authority to change, modify or otherwise alter the terms of the Buyer’s order or written agreement between the parties and the arbitrator’s decision shall be based on the information outlined in the warranty sections and other material from the Seller according to applicable state and federal law. Each party shall bear its own costs in such arbitration proceedings. Pending the resolution of the problem, the Buyer may proceed under the terms and conditions of the order and all documents incorporated therein. Buyer acknowledges that it has: (1) full knowledge of the hazards associated with the storage, distribution, and use of the Seller’s products; (2) Buyer assumes all responsibility for warning its personnel and any third parties of such hazards. It is the responsibility of the Buyer to comply with all statutes and regulations concerning the storage, handling, transportation and use of the Seller’s products shipped to Buyer by Seller.
|
|
Send mail to
orffman@sbcglobal.net with
questions or comments about this web site.
|
